Schumacher

DESIGNED ORIGINALLY FOR ''Tubby Insert; Front - CAT (pr)'' - gives more fill of the tyre carcass. 

THESE INSERTS HAVE BEEN PROVEN TO FIT PERFECTLY IN THE TT01E EURO TRUCK SERIES TYRES - WHEN YOU NEED A MORE DEMANDING CONTROL.

NOTE: This is Product CODE U6746 Schumacher Med Cat Front (but use on rear of TT01E truck tyres)

To Fit - Fold one side in, making a 'C' Shape, then insert and unpack.

TYRES SHOWN ARE FOR ILLUSTRATION ONLY AND ARE NOT INCLUDED. 

DESIGNED ORIGINALLY FOR ''Tubby Insert; Front - CAT (pr)'' - gives more fill of the tyre carcass. 

THESE INSERTS HAVE BEEN PROVEN TO FIT PERFECTLY IN THE TT01E EURO TRUCK SERIES TYRES - WHEN YOU NEED A MORE DEMANDING CONTROL.

NOTE: This is Product CODE U6746 Schumacher Med Cat Front (but use on rear of TT01E truck tyres)

To Fit - Fold one side in, making a 'C' Shape, then insert and unpack.

TYRES SHOWN ARE FOR ILLUSTRATION ONLY AND ARE NOT INCLUDED. 

For use on Polished Floor Surface - 20mm Wide.

USE IN COMBINATION WITH 20MM WIDE WHEELS. 

ALSO AVAILABLE IN 25MM (wide) VERSIONS

(USED AT BURGH RACE CLUB)

TO USE WITH SCHUMACHER SST 25MM WIDE MINIPINS TOURING CAR SIZE

Frosty Tip - After weeks of testing, and asking other pro drivers. We have found this to be the best product for the TT01E Euro Race Truck on Carpet.

SXT 3.0 was designed to provide superior performance in a minimum odour environment for both foam and rubber tyre racing. It has been engineered, tested and proven to be compatible with other additives. No worries about setup changes when switching compounds as SXT 3.0 provides the same on-track feel and performance as other additives. Another benefit we have noticed during the year is the ability to rejuvenate old foam tyres. In our tests we have taken 1 or 2 year old tyres and soaked them a couple times with SXT 3.0 and they tend to come back to "like new". Simply run them once and you have race ready tyres that you usually would have tossed away!

Carpet Foam and Rubber Tyre: Apply SXT 3.0 to clean tyres. Typically the entire rear tyres and a portion of the front tyres (starting at the inside edge) are coated, depending on traction conditions. Soak time before wiping is also dictated by traction conditions; longer soak = higher traction. Start by soaking the tyres for 15 minutes, timing it so that you wipe them 10 minutes before racing. Asphalt Foam: Apply SXT 3.0 to tires. Typically the entire rear tyres and a portion of the front tyres (starting at the inside edge) are coated, depending on traction conditions. Soak the tires for 20 to 30 minutes, timing it so that you wipe them 10 minutes before racing. Shorten soaking time if track is high bite.

Approx. 110 ml.

This is classed as a hazardous material by our shippers and consequently cannot be sent outside the UK.

DESIGNED FOR SCHUMACHER TIRES - MAY FIT OTHERS

-TYPE: FOAMS

-SCALE: 1/10TH

-4WD/2WD: SEE OPTIONS

-WIDTH: SEE OPTIONS DETAILS

-TYRE BEAD/RIM SIZE: 2.2INCH / 54MM DIAMETER

-HARDNESS: SEE OPTIONS

DESIGNED FOR SCHUMACHER TIRES - MAY FIT OTHERS

-TYPE: FOAMS

-SCALE: 1/10TH

-4WD/2WD: SEE OPTIONS

-WIDTH: SEE OPTIONS DETAILS

-TYRE BEAD/RIM SIZE: 2.2INCH / 54MM DIAMETER

-HARDNESS: SEE OPTIONS

The popular T style plug and socket with the addition of clip-on insulating caps from Amass. These caps replace the need for heatshrink tubing and provide extra grip.  As with the original connector, this new plug is made from nylon, making them very tough and difficult to melt when soldering. They have sprung steel blades to prevent the terminals coming apart accidentally and gold plated terminals for a good connection.

Backwards compatible with original T connectors so you can use them straight away.

It is recommended to always select the female deans plug for a battery terminal, to reduce the chance of short-circuits.

This Touring Car Wheel Arch Cutting Jig is a must for any Touring Car Racer.

The jig ensures accurate and repeatable cutting out of wheel arches time after time. One of the most tricky parts of body prep is now made super simple.

- Simply set your car to the required ride height and position the body shell to your desired height.

- Position the jig flush with the outside of the body shell and locate the centre of the axle through the hole in the tool. The end radius is different from side to side to prevent body tucks so ensure the jig's orientation is correct.

- Hold the jig and draw round the inside with a fine marker pen and then carefully cut to the line with a pair of curved scissors.

- The jig can also measure wing overhang with the handy 10mm step.

Introducing the 'Splinter' Tyre.

The Splinter tyre is a 2WD Slim ultra-low profile design for 1/10th Off Road buggies.

Especially suited to carpet and astro tracks.

Testing feedback has showed that the Splinter tyre has similar characteristics to the Low Profile Cut Stagger.  It has a safe driving feel but similar stronger steering feel compared to the Fusion Slim.

This has been achieved by reducing the side wall height which in turn reduces the movement of the carcass, adding to the carcass design our tread pattern and pin design has been developed to give stable but still a high level of steering.

Available in Yellow, Silver and Blue and Yellow Pre-glued option.

DESIGNED FOR SCHUMACHER TIRES - MAY FIT OTHERS

-TYPE: FOAMS

-SCALE: 1/10TH

-4WD/2WD: SEE OPTIONS

-WIDTH: SEE OPTIONS DETAILS

-TYRE BEAD/RIM SIZE: 2.2INCH / 54MM DIAMETER

-HARDNESS: SEE OPTIONS

Stylish toughened glass setup boards are ideal for setting up your 1/10th Touring, GT10, LMP12, GT12 or 1/10th Off Road buggies.

They are perfect for measuring ride height and camber and for providing a smooth, hard, easy clean work surface. They are not intended for 100% accurately measuring chassis flatness.

Also available separately are neoprene, zip up bags to protect your set up board during transportation. Also available with cool branded carry bag - see our other items G354 

Specs;

40x30cm
6mm Toughened Glass

• Schumacher Foam Strips 40 x 6 x 2mm thk - pk20

For use on Polished Floor Surface - 20mm Wide (SKINNY)

(USE WITH - 1/10 RC CAR SST Mini Pins 20mm wide (SKINNY) - Yellow (2pc) U6671)

(USED AT BURGH RACE CLUB)

The Shard is designed for the front of 1/10th 4WD vehicles.

Based on the very successful Fusion the new 4WD Shard has been developed to give the ultimate steering with good balance on high bite surfaces.

With our classic stagger pattern now utilizing a modernised geometry the Shard will enable the 4WD to have steering exactly where you need it.

Recommended insert: U6653 - Foam Tyre Insert; Hard - Rear - CAT (pr) as used in Pre-Glued.

SPEED PACK - Body Washers (pk 12). Soft foam washers fit onto your body posts and support the bodyshell. This makes your whole car run whisper quiet by preventing motor and road surface noise being transmitted by the body.

Use with standard GT12 Oval/Circuit Wheels.

The Rebel MTC body is sure to be a big hit at the track !  Proven shape and design matching modern Touring Car body trends.

The Rebel is supplied clear with overspray film, wing, mounting hardware and window and light masks.

No light or grill decals are included.

To suit 210 to 225mm wheelbase cars.

170mm Width

76 grams painted, ready to race.

Items needed to complete
Paint
Window Masking
Hobby Knife or Scissors for trimming
Stickers
Wing
Mirrors

DESIGNED FOR SCHUMACHER TIRES - MAY FIT OTHERS

-TYPE: FOAMS

-SCALE: 1/10TH

-4WD/2WD: SEE OPTIONS

-WIDTH: SEE OPTIONS DETAILS

-TYRE BEAD/RIM SIZE: 2.2INCH / 54MM DIAMETER

-HARDNESS: SEE OPTIONS