Tamiya RC Car Kits

• 1/10 scale R/C model assembly kit. Length: 434mm, width: 194mm, height: 120mm 
• Wheelbase: 257mm
• 1.0mm-thick polycarbonate body
• The efficient shaft-driven 4WD TT-02 chassis features superior adaptability and stability
• Black 16-spoke wheels are paired with racing slick tyres
• Includes stickers and window masking tape for use in the painting process
• Includes 540-Type Torque Tuned brushed motor and Hobbywing produced ESC

• Two-channel radio, steering servo, 7.2-7.4volt battery with compatible charger, and Tamiya PS polycarbonate paint

• 1/10 Scale
• Length: 464mm, Width: 184mm, Height: 136mm 
• Wheelbase: 257mm
• Tyre Width/Diameter (Front & Rear): 24/63mm
• Bathtub-type Frame
• Shaft Driven 4WD
• Front/Rear 4-Bevel Resin Differentials
• 3-Piece Steering Tie-Rod
• 4-Wheel Double Wishbone Suspension
• Front/Rear CVA Oil Shocks
• Gear Ratio = 8.27:1 (9 further ratios from 11.38:1 to 7.28:1 possible with use of separately-sold pinion)
• Type 540 Sport-Tuned Motor
• Full Ball Bearings
• Electronic Speed Controller (ESC) included

• Two-channel radio, steering servo, 7.2-7.4volt battery with compatible charger, and Tamiya PS polycarbonate paint

• 1/10 scale R/C model assembly kit. Length: 459mm
• Polycarbonate body was designed with access to the actual car’s CAD data for superb accuracy. Front and rear light cases are also moulded in polycarbonate
• Wheel arches are pre-cut out for a simpler body assembly experience
• The beginner-friendly, highly adaptable TT-02 is a versatile and easy to maintain shaft-driven 4WD chassis
• Separately moulded plastic components depict rear wing and side mirrors
• Racy 10-spoke wheels are moulded in gun metal and paired with slick tyres
• Stickers are included to create an original livery, as are masking stickers for use when painting
• Includes Tamiya Torque Tuned Motor
• Includes Tamiya TBLE-02S ESC (electronic speed control) capable of running sensor brushless motors and brushed motors alike (21.5 Turn BL motor limit / 23 Turn brushed motor limit)

• Two-channel radio, steering servo, 7.2-7.4volt battery with compatible charger, and Tamiya PS polycarbonate paint

• Length: 412mm, width: 197mm, height: 137mm 
• Wheelbase: 239mm (Long) 
• Tread: 148mm (front), 140mm (rear) 
• Tire width/diameter: 25/59mm (front & rear) 
• Bathtub type chassis 
• Front-midship motor, front-wheel drive 
• 4-bevel differential gear 
• 3-piece steering tie-rod 
• 4-wheel double wishbone suspension 
• Friction dampers 
• Gear ratio = 5.83:1 (using kit 29T pinion) 
• Type 540 motor 
• ESC included 

• Two-channel radio, steering servo, 7.2-7.4volt battery with compatible charger, and Tamiya PS polycarbonate paint

• 1/10 scale R/C model assembly kit 
• Length: 315mm, width: 167mm, height: 140mm.
• Wheelbase: 210mm (Short)
• Features updated markings for the body
• The form of the Mini Cooper Racing body is authentically recreated in lightweight polycarbonate
• Features 8-spoke wheels paired with 60D radial tyres
• Includes ESC (electronic speed controller)

• Two-channel radio, steering servo, 7.2-7.4volt battery with compatible charger, and Tamiya PS polycarbonate paint

Sporty Evolution of the TT-02!
This sporty evolution of the TT-02 chassis sees the efficient shaft-driven 4WD unit given newly-designed parts and gives users the ability to make setup adjustments across the board, making it great for racing! It is equipped with long reversible suspension arms, and rigid metal suspension mounts. The rear is set up with 3°of toe-in. CVA oil dampers are attached to specially-designed 3.0mm thick FRP damper stays, with optimum damper angle and rebound stroke providing excellent road holding. Turnbuckle upper arms and steering linkage allow fuss-free adjustment of camber and front toe. Power loss is minimized by the use of full ball bearings and metal cup joints and drive shafts.

Featured Components
_Reversible Suspension Arms _CVA Oil Shocks _FRP Front & Rear Damper Stays (newly-designed) _Metal Suspension Mounts (w/3°rear toe-in) _Metal Wheel Axles, Gearbox Joints & Drive Shafts _Full Ball Bearings _Turnbuckle Upper Arms & Steering Linkage _Die-Cast Metal Hex Wheel Hubs

• 3mm thick Front/Rear FRP Damper Stays (NEW part)
• Metal Suspension Mounts (NEW part)
• Item 51297 Reversible Suspension Arms (Long)
• CVA Oil Shocks
• Turnbuckle Shaft Front/Rear Upper Arms
• Turnbuckle Shaft Steering Tie-Rods
• Type 540 Torque Tuned Motor
• Item 51023 Medium-Narrow Racing Radial Tires
• Metal Cup Joints Metal Drive Shafts
• Die Cast Aluminum Hex Wheel Hubs

To celebrate the 50th anniversary of Tamiya’s first R/C model Porsche 934, this incredibly special limited-edition kit recreates the iconic Porsche 934 with a bespoke chassis featuring the motor positioned lengthwise at rear-center which powers the rear wheels just like the actual car. For collectors and shelf queen connoisseurs, magnetized body mounts (needing no body holes) are included for those who want to just display the R/C car as a model! A unique numbered plate is included to make each individual kit special.

About the bespoke chassis:

Motor Position

• Motor is positioned centrally and lengthwise to make the chassis layout like that of the actual car. Power is transmitted as follows: Pinion gear A → Spur gear → Propeller shaft → Pinion gear B → Spur gear → Gear differential. (Spur gears are new 66T design and all gears are 04 module. Gear differential is the one used on the TB-05 chassis.)
• Change pinion gears A and B to adjust gear ratio.
• Parts around gearbox are made of aluminum.
• Rear trailing arm
• Just like the actual car, the rear suspension uses trailing arms. Trailing arms are molded in carbon fiber reinforced plastic for superior rigidity.
• Glass fiber reinforced plastic lower deck
• The lower deck with integrated main and rear frames is molded in glass fiber reinforced plastic.
• The kit-standard wheelbase is 230mm (trailing arm rear suspension). (The rear layout of the lower deck can be altered to change the wheelbase to 251mm (double wishbone rear suspension). Separately sold body is needed for 251mm wheelbase.)
• Design features inspired by the actual car
• Motor guard shape is like muffler shape.
• Chassis underside patterns.
• Stay mount design is like intercooler design.
• Separately sold cooling fans are above the motor, like cooling fan duct of the actual car.

Body mounts

• Choose whether to mount the body using holes (driving model) or magnets and metal parts (display model).
• 1/10 scale R/C chassis assembly kit. Length: 435mm, width: 202mm, height: 130mm.
• This R/C model assembly kit recreates the Porsche 934 run by Kremer Racing, which flourished in the 1976 DRM (German Racing Championship) season.
• The 4-wheel independent suspension uses front double wishbone and rear trailing arm setups with TRF (Tamiya Racing Factory) dampers and stabilizers.
• The polycarbonate body is the one used for the Porsche 934 30th anniversary model. Paint body with PS-54 Cobalt Green. (item 86054)
• Separate plastic parts recreate the rear wing, side mirrors and light cases. Separately sold LEDs are attachable. Paint rear wing and side mirrors with TS-102 Cobalt Green. (item 85102)
• Gearbox parts and turnbuckle aluminum parts feature dark titanium anodized finish.
• Updated stickers for this edition are included.
• 2-piece mesh wheels with metal plated rims are paired with medium-narrow racing radial tires (Item 51023) which offer superior performance. Use wheel spacers (Item 53646) when changing to front narrow and rear wide.
• Features high-spec TRF (Tamiya Racing Factory) dampers.
• Universal drive shafts ensure efficient drive.
• Unique numbered plate included.
• Comes with Item 54298 1/10 Scale Touring Car Cockpit Set (Left-Hand Drive) with updated stickers.
• Inspired by the first Porsche 934 model, the kit comes in a white packaging.

Required to complete: 2-channel radio, steering servo, ESC, 540-motor, 7.2-7.4volt battery with compatible charger and Tamiya PS & TS paints.

Compatible Hop-Up Option parts

• Item 54704 TA07 Aluminum Steering Arm Set
• Item 54942 TRF420 Suspension Arm Bushing B (2pcs.)
• Item 54943 TRF420 Suspension Arm Bushing A-C (2pcs.)
• Item 54880 Aluminum Adjustable Suspension Mount (XB)
• Item 54884 Aluminum Adjustable Separate Suspension Mounts (A)
• Item 54543 Aluminum Cup Joints for TB-04 Gear Differential Unit (Long & Short) Item 53505 39mm Swing Shafts for Assembly Universal Shaft Set

Optional wheel and tire sets for the ultimate “stance” appearance on the shelf

• 50454 Racing Slick tires *2
• 50547 Wide Racing Slick tires *2
• 50548 2-piece Mesh Wheels *2
• 50549 2-piece Wide Mesh wheels *2
• 53646 Wheel spacer blue
• 53909 Tamiya LED Light Unit (TLU-01)

• This is a 1/10 scale R/C model assembly kit
• Length: 454mm, width: 189mm, height: 120mm
• Wheelbase: 251mm (short)
• The powerful form of the Mercedes-AMG GT3 EVO is captured in style by a lightweight, rigid polycarbonate body with separate polycarbonate front light cases (LED lights are not attachable), rear wing and canards 
• Separate black ABS plastic parts realistically depict side mirrors and rear wing stays
• The efficient shaft-driven 4WD TT-02 chassis features superior adaptability and stability
• Black mesh type wheels are paired with racing slick tyres
• Includes Item 53415 Touring Car Urethane Bumper Sponge to keep the body in top condition
• Comes with stickers and masking stickers for use in the paint job
• Carton quantity is 6 and EAN is 4950344587506

• Two-channel radio, steering servo, 7.2-7.4volt battery with compatible charger, and Tamiya PS polycarbonate paint

• 1/10 scale R/C model assembly kit. Length: 446mm, width: 192mm, height: 127mm 
• Wheelbase: 251mm
• The Audi 90 Quattro Racing is made of lightweight, rigid polycarbonate
• Separate red ABS plastic parts realistically depict distinctive side mirrors, a rear wing and air ducts
• Newly designed white dish wheels (+4mm offset) are paired with slick tyres
• The model utilizes the shaft-driven 4WD TT-02 chassis which features superior adaptability and stability
• Includes Item 51226 (Urethane Bumper L (TT-01, TGS)) to keep the body in top condition
• Includes: 540-size Tamiya Torque Tuned brushed motor and Hobbywing produced ESC

• Two-channel radio, steering servo, 7.2-7.4volt battery with compatible charger, and Tamiya PS polycarbonate paint

• This is a 1/10 scale R/C chassis assembly kit
• Equipped with front mid-ship, longitudinal motor position
• Changing rear section allows a choice from three wheelbases (short: 210mm, middle:225mm, long: 239mm) (ref. Image 3)
• Bathtub frame chassis and polycarbonate chassis cover plus front inside polycarbonate cover and rear section are newly-folded parts Mud guards helps prevent dirt and dust from getting inside
• New front C-hubs and rear uprights, plus lower suspension arms allow two types (about 8mm or 13mm) of ground clearances
• Caster angle can be set at 5 degrees by suspension mounts *For comparison, the XV-02 PRO chassis kit uses caster blocks which feature 6-degree caster angle (XV-01 chassis: 10-degree caster angle)
• The drivetrain employs oil-filled gear differential for front and rear
• Comes with two 39T differential gears and one 40T differential gear for adjustment of front and rear drive balance
• Use 39T gear (w/15T gear) on the front and 40T gear (w/15T gear) on the rear for drive balance bias to front and vice versa for drive balance bias to rear
• It features a longitudinal upright battery pack position in the centre-left for optimum balance
• Front bumper with skid angle contributes to reduce surface contact 
• Aluminium dampers are employed at the front and rear
• M-Chassis 11-spoke racing wheels (Item 51394) are paired with 60D rally block tires (Item 51427)
• Front and rear universal drive shafts come as standard
• Compatible with centre diff setup and separately sold slipper clutch
• Low-profile servo is recommended (Standard servo can be used, but it comes into contact with the front inside polycarbonate cover
• Please note that this chassis requires separately sold body, battery pack, motor, ESC and R/C equipment

• 1/10 scale R/C model assembly kit. Length: 468mm, width: 188mm, height: 120mm. Wheelbase: 257mm.
• Lightweight, rigid polycarbonate body with separate polycarbonate front and rear light cases (LEDs are not attachable) and canards.
• Separate black ABS plastic parts realistically depict distinctive side mirrors and a large rear wing.
• The model utilizes the shaft-driven 4WD TT-02 chassis, which features superior adaptability and stability.
• 6-spoke black wheels are paired with slick tires.
• Includes 540-bushed motor and ESC.
• Comes with livery stickers and masking window tape for use in the painting process.
• Requires: 2-channel radio, servo, 7.2-7.4volt battery & compatible battery charger, and Tamiya PS paint.

• 1/10 scale R/C model assembly kit. Length: 470mm, width: 194mm. Wheelbase: 257mm.
• 1997 Mercedes-Benz CLK-GTR is recreated in lightweight and durable polycarbonate.
• Separately moulded white ABS plastic parts recreate side mirrors and rear wing.
• Silver mesh wheels are paired with racing slick tires. (The rear wheels are wide tread.)
• TC-01 chassis
• The durable and composite monocoque-frame chassis provides shaft driven 4WD from a central motor via front and rear propeller shafts, with oil filled gear differentials.
• 4-wheel independent double wishbone suspension employs A-shaped long arms, plus inboard setups front and rear with oil dampers actuated by push rods and rocker arms.
• Use spacers and shims to easily alter camber, skid, and toe angle settings.
• Both suspension arms and uprights are identical left, right, front and rear, for more efficient pit work.
• Rear transverse battery position is also compatible with 139x47x25mm square-shaped battery packs.
• Required to complete: 2-channel radio, LOW-PROFILE steering servo, (Note: Standard Size Servos cannot be used), motor, ESC, 7.2-7.4volt battery with compatible battery charger, and Tamiya PS paint.

• This is a 1/10 scale R/C model assembly kit. Length: 450mm, width: 187mm, height: 136mm. Wheelbase: 257mm. 
• The lightweight, durable 1.0mm-thick polycarbonate body authentically captures the Toyota Celica GT-Four RC (ST185) in style.
• The model utilizes the efficient shaft-driven 4WD TT-02 chassis which features superior adaptability and stability. 
• 5-spoke wheels are paired with tread pattern racing radial tires. 
• Comes with stickers and masking stickers for use in the paint job
• Torque Tuned Motor & ESC included

• 1/10 scale R/C model assembly kit. Length: 427mm, width: 185mm, height: 145mm. Wheelbase: 257mm.
• Lightweight, durable 1.0mm-thick polycarbonate body.
• Separate plastic parts realistically depict side mirrors and rear wing element.
• Efficient shaft-driven 4WD TT-02 chassis features superior adaptability and stability.
• White 16-spoke wheels are paired with tread pattern racing radial tires.
• Comes with window masking stickers for use in the painting process.
• Includes 540 Torque Tuned Motor.
• Includes ESC.
• Requires 2-channel radio, steering servo, 7.2-7.4volt battery with compatible charger and Tamiya PS paints to complete.

• 1/10 scale R/C model assembly kit. Length: 397mm, width: 170mm, height: 142mm. Wheelbase: 239mm (L-size wheelbase spec). Lightweight polycarbonate body.
• Separately moulded plastic components recreate light cases, bumper, and side mirrors.
• The MF-01X chassis is at home on-road or on flat dirt, thanks to 4-wheel double wishbone suspension.
• Polycarbonate light cases are compatible with separately sold 5mm LEDs.
• Stickers are included to recreate body details.
• A host of Hop-Up Option parts are available to tune the MF-01X chassis.
• Includes 540 Torque Tuned motor and ESC.
• Requires 2-channel radio, steering servo, 7.2volt battery with compatible charger and Tamiya PS paint to complete.

• 1/10 scale R/C model assembly kit. Length: 395mm, width: 168mm, height: 121mm. Wheelbase: 210mm
• 1.0mm thick polycarbonate body
• Separate ABS plastic parts authentically depict headlights, front/rear bumpers and side mirrors
• The model is based upon the rear-wheel drive M-06 chassis (210mm wheelbase setup) featuring a rear-mounted motor
• Dish wheels moulded in silver are paired with 60D radial tires (Item 50683) at front and 60D super radial tires (Item 54999) at rear
• Stickers are included to recreate sponsor logos, race numbers and more.
• Window Masking stickers included to help aid the painting process of the body
• Type 540 motor and ESC included

• Two-channel radio, steering servo, 7.2volt battery with compatible charger, and Tamiya PS polycarbonate paint

This R/C assembly kit recreates the Opel Calibra V6 Cliff. The polycarbonate body is mounted on the TT-01 Type-E chassis, for ease of assembly. The Opel Calibra V6 Cliff was previously released on the Tamiya TA-02 chassis during the 1990’s touring car boom.

About the Opel Calibra V6 Cliff
The Opel Calibra V6 Cliff took part in the 1995 running of the Deutsche Tourenwagen Meisterschaft (DTM) series. Entered by Joest Racing with the driver JJ. Lehto, the car was powered by a 2.5-liter V6 engine capable of 420 hp. The distinctive black body with the Cliff logo caught people’s eye, and this car showed off race pace strength in DTM races.

• 1/10 scale R/C model assembly kit. Length: 448mm, width: 185mm, height: 128mm. Wheelbase: 257mm.
• Lightweight, rigid polycarbonate body (clear) with separate side mirrors and a rear wing.
• The model utilizes the shaft-driven 4WD TT-01 Type-E chassis, which is based around a durable bathtub frame and gives an intuitive, highly controllable driving experience.
• Features 4-wheel double wishbone suspension system.
• Silver ABS, dish wheels are paired with racing slick tires.
• Comes with stickers and window masking stickers for use in the paint job process.
• Includes Tamiya Torque-Tuned 540-brushed motor.
• Requires: 2-channel radio, steering servo, 7.2-7.4volt battery with compatible charger, and Tamiya PS paint.

Speedy and controllable 2 belt-driven 4WD chassis in TA series!
The Tamiya TA series continues to evolve. This iteration, the TA08 PRO, further evolves on-road touring car driving with this hopped-up chassis. The slim TA08 PRO Chassis Kit eliminates the need for an upper deck, which balances weight and rigidity. Its layout features the motor in near identical position to the TRF420, with the spur gear in front of the motor. Newly designed upper & lower arms make effective use of tire grip, equipped with laid down SSBB (Super Short Big Bore) dampers. This kit was based on Tamiya's extensive know-how built up through our traditional chassis series and data from racing, and offers plenty of potential for tuning.

• 1/10 scale R/C touring car assembly chassis kit.
• Features Stepped-V shaped main chassis which balances weight and rigidity.
• The battery pack and servo are positioned on a slight angle (about 10 degrees) to reduce surface contact while cornering and facilitate optimum weight distribution.
• Spur gear is positioned in front of motor which produces stable drivability.
• 2 belt-driven 4WD uses TRF420 oil-filled gear differentials and steel TA07 differential joint cups.
• A-arm suspension arm gives your model a low center of gravity, enhanced with laid down dampers.
• Camber and caster angles are adjustable by turnbuckle shafts and lower arm spacers respectively.
• Comes with Super Short Big Bore size shock dampers.
• Universal drive shafts and full bearings included.
• Rotating body mounts by 180 degrees switches between standard and 2mm advanced body positions. This feature allows the user to change the balance of the car with any selected body.
• Requires: 2-channel radio, short steering servo, ESC, motor, 190mm touring car body set, tires, 7.2-7.4 volt battery pack & compatible charger.

This TAMIYA R/C model assembly kit depicts the 1st-generation (T1) variant of the Volkswagen Type 2 van, which was introduced in 1950 and also known as the Volkswagen Bus to many of its legions of fans. Production of the actual van continued through until 1967. The iconic body is paired with the rear-wheel drive M-06 chassis for realistic fun driving just like the real RR Type 2 T1.

M-06 Chassis
The M-06 chassis features a Rear-Mounted Motor, Rear-Drive setup and features a longitudinally-mounted battery pack, with R/C radio gear positioned on either side for optimum balance and low center of gravity. 4-wheel double wishbone suspension is equipped with 60D radial tires at the front and 60D super grip tires at the rear. In addition, a 3-piece steering linkage offers nimble handling response.

• 1/10 scale R/C model assembly kit.
• Polycarbonate body with separate molded plastic parts included to create bumper, light cases and side mirrors.
• The M-06 chassis features a rear-motor, RWD setup with a longitudinally-mounted battery pack and R/C radio gear positioned on either side for optimum balance and a low center of gravity.
• 239mm wheelbase M-06L chassis.
• Metal-plated dish type wheels.
• Includes 540 motor.
• Includes Tamiya TBLE-02S ESC (electronic speed control) Capable of running sensor brushless motors and brushed motors alike. (21.5 Turn BL motor limit) (23 Turn brushed motor limit)
• Requires: 2-channel radio, steering servo, 7.2-volt battery pack & charger, and Tamiya PS paint.