MTC M-Chassis Leads, Plugs & Adaptors

Useful for connecting batteries with Deans connectors to speed controls with Tamiya plugs.

TO USE ON all SKY RC CHARGERS - TO CONVERT TO MALE DEANS PLUG TO CHARGE BATTERY FITTED WITH FEMALE DEANS (ALWAYS USE FEMALE DEANS ON BATTERYS TO PREVENT ANY SHORT).

TYPICALLY TO PLUG:

-FROM AN ESC FITTING WITH (MALE Tamiya Plug WHITE) > TO CONNECT AND ADAPT TO A BATTERY FITTED WITH A FEMALE (Deans T-Plug PLUG RED).

For use on 4mm bullet connector batteries to typical female deans T plug for balance charging.

For use on 4mm bullet connector batteries to typical female deans T plug for balance charging.

Designed for a Tamiya Battery Female output to accept a Males Deans

• T-plug (Deans) female battery plug to Tamiya male plug

w/PROTECTIVE SLEEVE

CONNECTOR (2) FOR RIGHT ANGLE

Awesome plug covers that help with the removal of your battery plugs. Plus, assist you in plugging in the correct polarity.

Super bling look!

Introducing the Cayote balance charge leads.

High reliability and quality with Cayote's signature colour.

Available in;

XT90 / 5mm 620mm
XT90 / 5mm 450mm
XT60 / 5mm 450mm

Introducing the Cayote balance charge leads.

High reliability and quality with Cayote's signature colour.

Available in;

XT90 / 5mm 620mm
XT90 / 5mm 450mm
XT60 / 5mm 450mm

Introducing the Cayote balance charge leads.

High reliability and quality with Cayote's signature colour.

Available in;

XT90 / 5mm 620mm
XT90 / 5mm 450mm
XT60 / 5mm 450mm

Parallel charging cable with XT60 to 4/5mm plug.  To suit many chargers including the SKY RC T1000 and neo D200.

Allows the power from both output ports to be combined to charge at a higher amp rate.

With balance charge lead.

This Charge Wire has a length of 50cm and comes with XT60 charger connection to Tamiya/JST battery connector.

Due to the 50cm Silicon-Flex cables and the high-end XT60 connector, this charging lead is perfectly suited for its application.

For protection and reliable operation, the charge wires come with a protection mesh and shrink tube on both sides with our logo imprinted.

The Charge Wire range for General Use is available with various connectors.

For use on 4mm bullet connector batteries to typical female deans T plug.

From MonkeyKingRC is this extremely handy Balance Charge Adapter Board.

Plug into the output of your charger using either the XT60 or 4mm bullet connectors and charge a wide variety of batteries with different connector types.

It has the ability to charge XT90, XT60, XT30, T plug and JST in 2S, 3S, 4S, 5S and 6S.

Extremely simple, but great to have at hand in any workshop or pit box.

This Charge Wire has a length of 50cm and comes with XT60 charger connection to BEC battery connector.

Due to the 50cm Silicon-Flex cables and the high-end XT60 connector, this charging lead is perfectly suited for its application.

For protection and reliable operation, the charge wires come with a protection mesh and shrink tube on both sides with our logo imprinted.

For use on 4mm bullet connector batteries to typical female Tamiya plug

• 4mm male plug to Tamiya plug 90° angle
• Included in the LRP LiPo Power/Hyper Packs with Multi Plug System
• Length 100mm

This excellent value ESC comes with a Deans-style connector and a Deans-Style-To-Tamiya adaptor lead, so is suitable for use in almost any brushed motor application.  These are branded Tamiya-Carson as they are ESCs that are currently arriving in some Tamiya kits (due to Tamiya not being able to source their own ESC due to chip shortages). 

SPECIFICATION AS FOLLOWS
Forward: Continues/Peak current 70A/360A
Backward: Continues/Peak current 40A/180A
Battery type: 2-3s Li-Po, 5-9 cells NiMH
Type of Model: 1:10 / 1:12 / 1/16 - ON Road, OFF Road, Boat
2s Lipo or 6 cells NimH: 540, 550 motor lowest 18 turn with 30000 rpm @ 7.2v
BEC Output Voltage: 3A/6v
Size: 34.5mm x 30.2mm x 18.7mm
Weight: 39g
Mode: Boat, Forward/Backward, Crawler
Sealing: Waterproof (Splash, Rain)

This ESC appears to be a Hobbywing 1060 unit rebranded.

Note JR is wired opposite to Futaba.

Note this version is wired common for Futaba and Etronix. JR is wired other way round.

Pre-soldered charging cable for charging all sorts of 2s batteries with the included balance port connector. This version comes with a XT60 for you to plug into your charger.

4MM BATTERY BULLETS AND 2MM BULLET FOR BALANCING

Feature:

• For: Charger

• Material: Metal/Plastic

• Color: Black/Red/Gold

• XT60 PLUG FOR ALL SKY RC CHARGERS

Include:

• Charge Cable (1 pc)

Great charging lead from Monkey King RC for charging receiver and transmitter packs. 

XT60 input connectors and Futaba output.

Robust braided design.

Approx 32cm.

Awesome plug covers that help with the removal of your battery plugs. Plus, assist you in plugging in the correct polarity.

Super bling look!

The Voltz Lipo Locker is intended to reduce and minimise the chances of damage in the event of a LiPo battery fire.

Wise up and use LiPo protection. The alternatives are not worth thinking about.

Dimensions: 18.5cm x 7.5cm x 6cm.

VOLTZ CHARGE VAULT LIPO SACK/BAG MEDIUM 22cm x 18cm

Protect your family and home from the hazard of LiPo charging.

This Voltz Vault is a fireproof bag is intended to reduce and minimise the chances of damage in the event of a LiPo battery fire caused by incorrectly or poorly functioning LiPos, especially during charging.

We urge all customers to always practice extreme caution when charging and never leave a charging battery unattended.

Specifications

Dimensions: 22cm x 18cm